EPDM membrane
The rubber membrane is adhered or fastened in black or white.
Flat Roofing
Rubber Roof Installation Nutley, NJ
A Nutley roofer who installs EPDM can put a new rubber roof on a flat or low slope section of almost any home, with as few seams as possible. One call to (973) 858-1824 reaches a nearby rubber roof installer.
EPDM is the material most people mean when they say rubber roof. It comes in large, flexible sheets, most often black, in 45 or 60 mil thickness, and its biggest strength is that it stays flexible in heat and cold without cracking. That flexibility is why it suits so many homes.
Attachment method shapes the rest of the installation. The sheet can be glued to the substrate, fastened with plates at the seams or laid loose under a layer of stone. On most homes, fully adhered EPDM is the usual choice because it handles wind well and stays smooth.
Then comes thickness and color. Thicker 60 mil membrane stands up better to foot traffic and hail. Black EPDM absorbs heat, which helps in cold climates, while white EPDM reflects sun and keeps rooms below cooler. Where the rubber meets a shingled roof or the house wall, the tie-in detail matters as much as any of these choices.
If the problem goes deeper than it first looked, a Nutley roofer may also recommend rubber roof repair or flat roof installation.
Looking for Nutley rubber roof installation? Call (973) 858-1824 to reach a nearby roofing contractor.
Call nowThe process
What happens during a rubber roof installation
Here is how a roofer typically installs an EPDM roof.
Prepare the deck
The roofer checks the deck for rot, gaps and loose sheets and confirms the roof has enough slope to drain. A tear-off comes first on existing roofs.
Insulation
Rigid insulation, often polyiso, is fastened with plates and screws, then a cover board goes on top. Low spots can be corrected with tapered insulation.
Sheet layout
Wide sheets are laid out to cover the roof with as few seams as possible, then allowed to relax. Laps are arranged so water flows over them.
Bond the membrane
Bonding adhesive is rolled onto both the cover board and the underside of the rubber, then the sheet is folded back down and broomed smooth. Then the other half is done the same way. Brooming from the middle outward pushes trapped air to the edges.
Seal the seams
Seam areas are cleaned and primed, then seam tape is applied and rolled firmly with a seam roller. Tape edges are finished with lap sealant.
Flash the details
Perimeter edge metal, wall flashing and pipe boots complete the roof. The top edge is sealed and covered. The last step is probing each seam and patch for gaps.
What is included
What goes into a rubber roof
Tear-off
The base is cleared and checked for a sound start.
Seams
Every seam gets primer and tape and is checked before closeout.
Flashing
Termination bar, pipe boots and edge metal are installed for a finished roof.
Cover board
Insulation adds energy savings and slope for a smooth surface.
Related service
EPDM Roof Installation Nutley, NJ
Installing EPDM well comes down to preparation, seams and flashing. The membrane has to lie flat on a clean, dry cover board, the adhesive has to reach the right tack before the sheet is laid and every seam has to be primed and rolled with care. Weather matters too, since adhesives and primers need dry conditions. The field and the flashings may get different adhesives, since vertical surfaces need a stronger grip.
In Nutley, an experienced EPDM installer leaves room for the membrane to move and age. Securing the membrane at the edges and flashing corners correctly prevents later tears. Ask how the roofer secures the perimeter.
Local help
Rubber Roof Installation Near Me
Rubber roofs in Nutley are common on porches, garages, additions and flat sections of older homes. Across Nutley and nearby towns like Glen Ridge, Rutherford, North Arlington and Clifton, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, and the right installer makes a big difference.
Need rubber roof installation around Nutley? Call (973) 858-1824 for a Nutley roofer who serves the towns around it too.
How the weather here affects roofs around Nutley
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Nutley, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why act early
Smaller repairs
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers who know Nutley
Local roofers see the same roofs and storm damage across Nutley and nearby towns.
Know what happens next
Ask your questions before you agree to anything.
Rubber Roof Installation questions
What is the lifespan of a new EPDM roof?
Rubber roofs often last decades. Good seams, drainage and occasional checks make the difference. Repairs are simple when needed.
What is the difference between EPDM and TPO?
The two are different materials. Black EPDM is taped and stretchy, and white TPO is welded and reflective. A roofer can help you choose.
Which EPDM thickness should I choose?
EPDM usually comes in 45 or 60 mil for homes. Thicker 60 mil is tougher and longer lasting. Thicker 90 mil membrane exists for heavy use.
Should my rubber roof be black or white?
Color affects heat gain. White helps in sunny climates, and black is common where winters are long. A roofer can recommend what fits your home.
Can a rubber roof go over an existing roof?
EPDM can sometimes go over an existing roof. There should be only one existing layer, the insulation must be dry and a cover board or recover board goes between the old roof and the rubber. Wet insulation or multiple layers mean a tear-off. A moisture check of the old roof settles the question before any work is planned.
More questions? Call (973) 858-1824
Related services
Rubber Roof Repair
Repairs for leaking rubber roofs, from peeling seams to pulled flashing at walls and curbs, after the real leak point is found.
Learn moreFlat Roof Installation
Installing TPO, PVC, EPDM or modified bitumen roofs on additions, garages, porches and flat-roof homes, so water drains instead of ponding.
Learn moreTPO Roofing
Heat-welded TPO membrane for flat and low-slope roofs, built around proper drainage, flashing and edge metal.
Learn moreFlat Roof Replacement
Full replacement of failing flat roofs, with a moisture survey deciding tear-off or recover, with tapered insulation where water used to sit.
Learn more
Looking for something else?
See all roofing servicesNeed rubber roof installation in Nutley, NJ?
Call (973) 858-1824 for a local roofer in Nutley and nearby towns.